IGNITION COIL Not Available USER.bfc44c53-62ab-404f-ae5c-d06bbf3a0875 YAMAHA YFM100 CHAMP YFM 100 NEW IGNITION COIL 1987-1991
Returns Accepted Safe and secure paymentsSafe and secure payments. 100% Satisfaction Guaranteed
YAMAHA YFM100 CHAMP YFM 100 NEW IGNITION COIL 1987-1991

YAMAHA YFM100 CHAMP YFM 100 NEW IGNITION COIL 1987-1991

$31.49
$34.99 (10% off)
About this Item
Available stock:2
Location: Orem, Utah

Returns: Accepted
Condition: New
Share:
About the Seller
Shipping Handling time and Shipping policy

Manufacturer Part Number : [Does Not Apply]
Part Brand : [87 1988 88 1989 89 1990 90 91]
Brand : [IGNITION COIL]
Item Specifics
eBay
PART FOR SALE IS: A NEW AFTERMARKET IGNITION COIL
LOCATION: C Y 1 AT K  CRUCY1 CY1
NEW, NEVER USED. GREAT CONDITION. 

COIL FITS YAMAHA :
-1987-1991 YAMAHA YFM100 CHAMP

***This coil MAY require modification of the mounting area to fit properly***

MEASUREMENTS:
- THE MOUNTING TABS ARE ABOUT 2 3/4 INCHES LONG, END TO END.
- MOUNTING TABS ARE ABOUT 3/8 INCHES WIDE, ABOUT 5/16 INCHES THICK.
- MOUNTING HOLES ARE ABOUT 2 1/8 INCHES CENTER TO CENTER.
- MOUNTING HOLES ARE ABOUT 3/8 INCHES LONG, ABOUT 1/4 INCH WIDE.


YOU ARE BUYING EXACTLY WHAT IS PICTURED, NO OTHER PARTS ARE INCLUDED.  ***This coil MAY require modification of the mounting area to fit properly***

This coil meets or exceeds OEM specifications. It comes with a wire adapter so it will fit many applications. Your application may or may not use this wire. In some cases, you may need to use your existing spark plug boot/wire. If you need to remove the spark plug wire out of this coil, you just untwist it & you can install your existing spark plug wire.  Please email with any questions.



Customer Reviews

Four and Half Stars
4.8 out of 5 stars based on 15 reviews
Five Stars
Works as it should!
Works great on Yamaha Kodiak 400.
By
Five Stars
Works for 99 Kodiak
Works good for a 99 Kodiak yfm400. Boot is a little short but it gets the job done.
By
Five Stars
Great
Exactly as described.
By
Five Stars
Bonne pièce
Vtt
By
Five Stars
Perfect
It worked perfect for my quad
By
Five Stars
1995 Wolverine never ran this well
I pulled out the throttle cable tube, tapped the retainer hole next to it (no threads at all), put the original tube and retainer in. Double checked the seat and needle worked, and installed. The hardware supplied was too big for me to bolt the carb boot on, had to use the smaller OE nuts, and you could tell the boot was thicker, as the nut still caught on each revolution. All sealed up and running better than ever! FACT: if your boot is blown, ADJUST YOUR VALVES! Then replace the boot.
By
Four Stars
Not a direct fit but doable.
Easy to install. Old carb has a choke control above the handlebars that connects to the top of the carburetor. New one does not, the choke is a pull lever on the carb. I have two wires floating above the carb that used to be connected to the old one. The pull choke on the new carb does not clear the fuel feed line so I had to chop off the black knob. Will have to use a pliers each time to pull the choke.
By
Five Stars
1995 Wolverine never ran this well
I had to modify it a bit to get the dual throttle cable to connect properly, though the main throttle cable is a bit too tight. All in all, the big bear now runs better than it’s ever run since I bought it. This was the last piece of what I call project “don’t freeze to death” since the big bear is my snow plow. And what a plow it is now! Thank you!
By
Four Stars
Near direct replacement for moto-4
Received the carb pretty quickly. Installed it last night on my 97 warrior. Took it out today and tested it. Works flawlessly. The intake fit. Only issue was the throttle cable inlet was angled wrong. Was able to bend it to the right position.
By
Five Stars
Fit my ‘88 big bear 350
It was perfect
By
Five Stars
Works better then expected.
Good fit
By
Five Stars
Just what my husband wanted
Value for your money. Easy to install
By
Five Stars
Good
Works good
By
Five Stars
Jp
Perfect fit on my 03 yamaha warrior 350 started right up runs perfect. Rubber boot around idle controll rod was not clipped into place and would have caused issues but was obvious and very easy to push into place.
By
Five Stars
1995 Wolverine never ran this well
Showed up remarkably quick. It bolted rite up and required no jetting or fiddling,set the idle and I was riding.normally I would rebuild my old one, but this was very cost effective. Couldn’t be more satisfied with the whole process.
By
Back
Truegether Logo
About This Item
Item Specification